Skip to main content

Raytools BM115 Consumables: D28 M11 Ring, 37 mm Windows

BM115 is the high-power branch of the BM family

The Raytools BM115 is rated 6 / 8 / 12 kW across its versions, with a QBH / QD / Q+ fibre interface and a clear aperture of 35 mm (36.1 mm on the 12 kW version). Both the collimating and the focusing optics are water cooled — that is the design change that separates it from the mid-power heads, and it is also the reason its consumables behave differently.

Its parts list has one counter-intuitive feature: a high-power head on the small D28-M11 ceramic ring. People expect 12 kW to mean the bigger ring, order D32-M14 nozzles, and find out at the machine. The ring is set by the head's nozzle assembly, not by its power rating.

Parts that follow a BM115

PartWhat fitsWhat decides it
Ceramic ringD28-M11 (D28-H12-M11)Ring diameter and M11 thread; shared with BM114 / BT220 / BS06K
NozzleD28 body, 15 mm tall, M11; single and double layerBore to the thickness and gas; the high-power build runs larger bores than a 3 kW head
Protective window — upper37 × 1.6 mmSits at the collimator side
Protective window — lower37 × 7 mmFocus side; the high-duty section
Focus moduleFL150 / FL200, water cooledMarking on the module; thick plate is the reason this head exists
Collimating lensCL100Paired with the focus lens

Power, aperture, focal length and cover-glass figures as published by Raytools for the BM115 series, read 2026-11-21. Nozzle bore range varies with the version — confirm against the nameplate.

37 × 1.6 and 37 × 7: the pair that gets mixed up

Both are 37 mm across. The listing photos look identical. They are 5.4 mm apart in section and they are not interchangeable in either direction.

  • 37 × 1.6 is the thin section used on the collimator side. Its job is to keep dust and fume off the collimating lens without adding much glass to the beam path.
  • 37 × 7 is the thick section on the focus side. The thickness is thermal mass: at 6–12 kW the window has to carry heat away from the beam area faster than a thin section can, or the coating fails and the focus lens behind it follows.

This is the single most common wrong-part order we see on high-power heads, and it usually surfaces as “the window will not seal” or “the head reports a gas fault” — because a thinner window does not compress the seal the way the seat expects.

BM115, BM114 and BM114S: same ring, different generation

All three sit on the D28-M11 ring, so nozzles and ceramic rings cross between them. What does not cross reliably is the optics: the BM115 introduced water-cooled collimating and focusing modules and a larger clear aperture, and the window sizes moved with that change. Treat the ring as shared and the optics as head-specific, and order the optics against the module marking.

Where BM115 orders go wrong

  • Ordering D32 nozzles because the power is high. BM115 is D28-M11. D32-M14 belongs to the BT240 / BM109–111 branch.
  • Swapping 37 × 1.6 and 37 × 7. Same diameter, different section, different seat compression.
  • Buying a window without the O-ring or seal. High-power drawers rely on the seal to keep the optical chamber clean; a reused, hardened seal undoes a new window.
  • Assuming the 12 kW version takes the same nozzle bore as the 6 kW one. The bore range widens with the version — check the process table, not the family name.

How to confirm before ordering

  1. Nameplate photo — BM115 with its version (2.0 / 3.0) and power rating.
  2. The old ceramic ring measured across its outer diameter — 28 mm confirms the M11 branch.
  3. Both windows out of the head, measured: 37 × 1.6 upper and 37 × 7 lower. If only one comes out easily, photograph the other in place with a rule.
  4. Tell us the thickness range you cut; that decides the focus module and the nozzle bore together.

FAQ

Is the BM115 a 6 kW or a 12 kW head?

It is both, depending on the version: the series is rated 6 / 8 / 12 kW, and the 12 kW build has a slightly larger clear aperture. The consumables overlap heavily, but the nozzle bore range and the optics should be confirmed against the nameplate rather than assumed from the model number.

Does the BM115 use D28 or D32 nozzles?

D28 with an M11 thread. That surprises people because the head is high power, but the ring is set by the nozzle assembly design, and this branch of the family stayed on D28-M11.

Can I use a 37 × 1.6 window in the lower position?

No. The lower position takes 37 × 7. The thin section does not fill the seat, so the seal is not compressed and the head will report a gas or vacuum fault — if it seals at all.

Related categories

Ruiying is an independent supplier of aftermarket laser consumables. Brand names are used only to indicate compatibility and remain the property of their respective owners. We are not affiliated with, authorised by, or endorsed by these manufacturers. Specifications vary between head revisions — please confirm the full model before ordering.

About

Yangzhou Ruiying International Trade Co., Ltd. specializes in laser cutting consumables, optics and machine parts — serving distributors, service centers and OEMs worldwide from Yangzhou, Jiangsu, China.